<think>

1. A calibration manual for a precision instrument defines reference standards, calibration intervals, environmental conditions, and acceptance limits for each measurement function.
2. An infrared thermometer calibration manual specifies emissivity settings, target-to-spot ratio, ambient temperature range, and black-body reference requirements.
3. A digital multimeter calibration manual commonly covers DC voltage, AC voltage, DC current, AC current, resistance, continuity, and capacitance functions.
4. A slide caliper calibration manual specifies zero-offset verification, jaw parallelism, scale graduation checks, and gauge block reference measurements.
5. Manufacturer warranties for precision instruments commonly cover defects in materials and workmanship for a stated period, often one year from date of purchase.
6. Warranty terms frequently exclude damage caused by misuse, unauthorized repair, corrosion, improper storage, or failure to follow the calibration manual.
7. A calibration certificate should identify the instrument serial number, calibration date, reference standards used, measured values, uncertainties, and traceability statement.
8. Source-grounded QA requires that each calibration result be linked to a specific manual revision, certificate number, and approved reference standard.
9. Infrared thermometers require emissivity correction because surface finish, oxidation, and material composition affect emitted infrared radiation.
10. Digital multimeter accuracy specifications are often expressed as a percentage of reading plus a number of counts, such as 0.05% + 2 counts.
11. Slide caliper resolution is determined by the smallest scale division, commonly 0.01 mm or 0.001 in, depending on the instrument model.
12. Calibration intervals for precision instruments are set based on usage frequency, observed drift, risk of measurement error, and applicable quality-system requirements.
13. A calibration manual may require pre-calibration inspection for physical damage, battery condition, connector wear, and contamination of optical or contact surfaces.
14. Warranties for battery-powered instruments may require use of specified battery types and may exclude damage from battery leakage.
15. QA records for an infrared thermometer should include target temperature, reference black-body temperature, measured temperature, deviation, and emissivity value used.
16. Digital multimeter calibration often uses a calibrated source meter or standard resistor set with documented uncertainty and traceability.
17. Slide caliper calibration commonly uses gauge blocks of known dimensions to verify measurement at multiple points across the measuring range.
18. A calibration manual should state the maximum permissible error or tolerance band that defines pass/fail status for each measurement point.
19. Warranty claims for precision instruments generally require proof of purchase, serial number, and evidence that the failure is not due to operator error.
20. Source-grounded QA means that calibration decisions must cite the controlling document, such as the manufacturer manual, internal procedure, or customer specification.
21. Infrared thermometer calibration may be performed against a black-body source, a contact thermometer reference, or a certified temperature standard.
22. Digital multimeter calibration records should include applied test values, measured values, deviations, and uncertainty contributions from the reference standard.
23. Slide caliper zero adjustment must be verified with closed jaws, and any residual offset should be recorded before calibration measurements.
24. Calibration manuals often require environmental conditions such as 20 °C ± 5 °C and 30% to 70% relative humidity for dimensional measurements.
25. A warranty may become void if the instrument is opened by unauthorized personnel, except where local law requires repair rights.
26. QA for precision instruments includes verification that calibration labels are legible, current, and consistent with the calibration certificate.
27. Infrared thermometer specifications may include measurement range, accuracy, response time, and optical resolution, all of which must be checked against the manual.
28. Digital multimeter input protection ratings define maximum safe voltage or current limits that must not be exceeded during calibration or use.
29. Slide caliper wear on the measuring faces can introduce systematic error, so calibration should include inspection for burrs, dents, and surface contamination.
30. A calibration manual should define the action to take when a measurement falls outside acceptance limits, such as adjustment, repair, or quarantine.
31. Warranty documentation should state whether calibration services, consumables, and shipping are included or excluded from the warranty period.
32. Source-grounded QA requires retention of calibration data, certificates, manual revisions, and operator records for the defined retention period.
33. Infrared thermometer calibration should account for ambient temperature effects on the sensor and electronics, as specified in the manual.
34. Digital multimeter calibration may include verification of input impedance, common-mode rejection, and safety insulation where applicable.
35. Slide caliper calibration results should be recorded with the gauge block size, measured value, deviation, and uncertainty of the reference gauge block.
36. A calibration manual revision history provides the document control needed to confirm which procedure version governed a specific calibration event.
37. Warranty coverage for an infrared thermometer may depend on use within the stated optical range and avoidance of exposure to temperatures beyond the manual limits.
38. Digital multimeter calibration should verify that the display resolution, input range, and auto-range behavior match the specifications in the calibration manual.
39. Slide caliper calibration should verify both the main scale and vernier or digital readout against reference gauge blocks at low, mid, and high range points.
40. Source-grounded QA for a digital multimeter requires recording the reference standard’s calibration due date, uncertainty, and traceability to a national or international standard.
41. An infrared thermometer warranty may exclude damage from lens contamination, window fouling, or exposure to high-temperature radiation beyond the rated target range.
42. Calibration manuals for digital multimeters often require verification of input protection, fuse condition, and terminal integrity before applying test signals.
43. Slide caliper warranty terms commonly exclude wear of measuring faces caused by excessive force, impact, or measurement of hardened or rough surfaces.
44. QA records should state whether calibration was performed by the manufacturer, an accredited laboratory, or an internal qualified technician.
45. A calibration manual may require post-calibration verification to confirm that adjustments have not shifted other measurement functions outside tolerance.
46. Infrared thermometer calibration data should include the reference source uncertainty, target emissivity, distance-to-target ratio, and ambient temperature.
47. Digital multimeter calibration may require verification of low-current ranges using a calibrated current source with documented source impedance.
48. Slide caliper calibration should record the force applied during measurement if the manual specifies a maximum measuring force.
49. Warranty documentation should identify whether the warranty is transferable, region-specific, or limited to the original purchaser.
50. Source-grounded QA requires that any deviation from the calibration manual be documented, approved, and linked to a risk assessment.
51. An infrared thermometer calibration manual may specify a warm-up time before calibration to stabilize the sensor and electronics.
52. Digital multimeter calibration records should include the calibration standard’s last calibration date and its measurement uncertainty at each test point.
53. Slide caliper calibration should verify that the locking screw or lock mechanism does not alter the zero position or jaw alignment.
54. A warranty may require return of the instrument in its original packaging, with accessories, documentation, and calibration labels intact.
55. QA for precision instruments should verify that calibration labels show the calibration date, next due date, and responsible technician or laboratory.
56. Infrared thermometer specifications may state accuracy as a percentage of reading or a fixed temperature deviation, and the calibration manual must define the test method.
57. Digital multimeter calibration should include checks for input offset, gain error, and range switching behavior across all active ranges.
58. Slide caliper calibration should include verification of the depth rod or pin, if equipped, using a reference depth gauge block or calibrated step.
59. Warranty terms may exclude coverage for consumable parts such as batteries, fuses, probes, and protective covers unless stated otherwise.
60. Source-grounded QA requires that calibration software, if used, be validated and that its version be recorded in the calibration record.
61. A calibration manual may require periodic verification of the reference standards used to calibrate the infrared thermometer, digital multimeter, or slide caliper.
62. Digital multimeter warranty claims may require demonstration that the failure occurred under normal operating conditions defined in the manual.
63. Slide caliper calibration should record the reference gauge block’s dimensional uncertainty, including wear allowance and temperature correction.
64. Infrared thermometer calibration should be repeated after any repair, battery replacement, or firmware update if the manual requires it.
65. QA records should include the environmental conditions at the time of calibration, including temperature, humidity, and pressure where relevant.
66. A calibration manual may define a minimum number of measurement points for each range to ensure statistically meaningful verification.
67. Digital multimeter calibration may require verification of safety ratings, such as CAT category, using a qualified test setup.
68. Slide caliper warranty may exclude damage from measuring workpieces that are hot, wet, abrasive, or contaminated with debris.
69. Source-grounded QA means that a pass/fail decision must be traceable to the numerical acceptance criteria in the controlling calibration manual.
70. Infrared thermometer calibration should include a check of the optical axis alignment if the manual specifies aiming or focus requirements.
71. Digital multimeter calibration records should note any observed drift beyond the stated accuracy specification and the corrective action taken.
72. Slide caliper calibration should verify that the measuring faces are clean, flat, and free from burrs before applying gauge blocks.
73. A warranty may require that calibration be performed only by authorized service centers to maintain coverage.
74. QA for precision instruments should include review of the calibration manual for superseded revisions before performing the calibration.
75. Infrared thermometer calibration may require a reference thermometer with a stated accuracy better than the instrument under test.
76. Digital multimeter calibration should verify that the instrument’s self-test or error indicators function correctly after calibration.
77. Slide caliper calibration should record the measured value at each gauge block size and compare it to the nominal value plus tolerance.
78. Warranty documentation should state the remedy for a covered failure, such as repair, replacement, or refund.
79. Source-grounded QA requires that calibration certificates be archived with the instrument record and made available for audit.
80. A calibration manual may require calibration of an infrared thermometer at multiple target temperatures across its full range.
81. Digital multimeter calibration should include verification of the instrument’s input protection against overvoltage or overload conditions.
82. Slide caliper calibration should verify that the digital display, if present, matches the mechanical scale within the stated resolution.
83. Warranty coverage may be limited to the original calibration interval and may not cover drift caused by excessive use.
84. QA records should identify the calibration standard’s traceability chain, including the reference laboratory and measurement standard.
85. Infrared thermometer calibration should account for background radiation effects if the manual specifies background temperature compensation.
86. Digital multimeter calibration may require verification of the instrument’s response time for fast transient measurements.
87. Slide caliper calibration should include a check for backlash in the sliding mechanism if the manual specifies a backlash limit.
88. A warranty may exclude coverage for instruments that have been exposed to solvents, cleaning agents, or chemicals not listed in the manual.
89. Source-grounded QA requires that any manual deviation be approved by a qualified authority and documented in the QA record.
90. Infrared thermometer calibration should record the target material, surface finish, and emissivity value used for the measurement.
91. Digital multimeter calibration should verify that the instrument’s range selection is stable and does not shift during repeated measurements.
92. Slide caliper calibration should verify that the measuring range covers the full scale and that the end stops are undamaged.
93. Warranty terms may require that the instrument be returned with its calibration certificate and original accessories.
94. QA for precision instruments should include verification that the calibration label matches the certificate and the instrument serial number.
95. Infrared thermometer calibration may require a black-body source with a temperature stability better than the thermometer’s accuracy specification.
96. Digital multimeter calibration should include verification of the instrument’s common-mode rejection ratio if specified in the manual.
97. Slide caliper calibration should record the temperature of the gauge blocks and apply the thermal expansion correction if required.
98. A warranty may exclude coverage for damage caused by static discharge, lightning, or power surges unless surge protection is specified.
99. Source-grounded QA requires that calibration data be reviewed for outliers, measurement uncertainty, and compliance with acceptance criteria.
100. A complete calibration record for an infrared thermometer, digital multimeter, or slide caliper should include the manual revision, reference standards, results, uncertainty, and approval signature.
101. Calibration manuals for precision instruments often require periodic re-verification after repair to confirm that the repair did not affect measurement performance.
102. Warranty coverage for a digital multimeter may depend on use of the specified input terminals and avoidance of measurements above the rated safety category.
103. Slide caliper calibration should verify that the measuring faces remain parallel over the full stroke, as specified in the calibration manual.
104. QA records should state whether the calibration was performed in the field or in a controlled laboratory environment.
105. Infrared thermometer calibration should include a check of the instrument’s low-battery indicator if the manual requires it.
106. Digital multimeter calibration may require verification of the instrument’s input impedance for high-impedance voltage measurements.
107. Slide caliper calibration should record the force used to close the jaws and the resulting zero offset.
108. A warranty may exclude coverage for instruments that have been modified, including software changes not authorized by the manufacturer.
109. Source-grounded QA requires that the calibration manual be the current controlled revision at the time of calibration.
110. Infrared thermometer calibration should verify that the instrument’s temperature reading agrees with the reference within the stated accuracy.
111. Digital multimeter calibration should include verification of the instrument’s continuity test threshold and beep function.
112. Slide caliper calibration should verify that the vernier scale or digital readout is aligned with the main scale at zero.
113. Warranty documentation should state the warranty start date, end date, and any conditions that extend or shorten the coverage period.
114. QA for precision instruments should include review of the instrument’s service history before calibration.
115. Infrared thermometer calibration may require verification of the instrument’s response time at high and low target temperatures.
116. Digital multimeter calibration should verify that the instrument’s AC measurement bandwidth matches the manual specification.
117. Slide caliper calibration should record the measured length at multiple gauge block sizes and calculate the maximum deviation.
118. A warranty may require that the instrument be stored within the temperature and humidity limits stated in the manual.
119. Source-grounded QA requires that calibration results be signed by a qualified person and retained in the quality record.
120. Infrared thermometer calibration should include a check for optical window cleanliness and alignment before measurement.
121. Digital multimeter calibration may require verification of the instrument’s fuse rating and replacement procedure.
122. Slide caliper calibration should verify that the depth measuring pin extends and retracts smoothly without binding.
123. Warranty coverage may be limited to the first year of service and may not cover normal wear of mechanical parts.
124. QA records should include the calibration standard’s calibration certificate number and expiration date.
125. Infrared thermometer calibration should record the ambient temperature and the target temperature used for each calibration point.
126. Digital multimeter calibration should verify that the instrument’s display updates correctly after range changes.
127. Slide caliper calibration should verify that the measuring faces make full contact with the gauge block across the entire face.
128. A warranty may exclude coverage for damage caused by improper handling, dropping, or impact.
129. Source-grounded QA requires that any calibration failure trigger a documented corrective action and re-verification.
130. Infrared thermometer calibration may require a reference source with a known emissivity and a stable temperature output.
131. Digital multimeter calibration should verify that the instrument’s input terminals are securely connected and free from corrosion.
132. Slide caliper calibration should record the gauge block’s nominal dimension, measured dimension, and deviation.
133. Warranty documentation should state whether the warranty covers labor, parts, or both.
134. QA for precision instruments should include verification that the calibration manual is accessible to the technician performing the calibration.
135. Infrared thermometer calibration should verify that the instrument’s emissivity setting matches the target material.
136. Digital multimeter calibration may require verification of the instrument’s auto-power-off function if specified.
137. Slide caliper calibration should verify that the locking mechanism does not introduce play into the measurement.
138. A warranty may require that the instrument be calibrated at intervals specified in the manual to maintain coverage.
139. Source-grounded QA requires that calibration data be backed up and stored in a controlled record system.
140. Infrared thermometer calibration should include a check of the instrument’s temperature range limits.
141. Digital multimeter calibration should verify that the instrument’s measurement functions are not affected by adjacent range errors.
142. Slide caliper calibration should verify that the scale graduations are legible and not worn.
143. Warranty coverage may be void if the instrument is used outside its specified environmental conditions.
144. QA records should include the name, qualification, and signature of the person performing the calibration.
145. Infrared thermometer calibration should record the distance from the instrument to the target if the manual specifies a minimum distance.
146. Digital multimeter calibration may require verification of the instrument’s safety insulation resistance.
147. Slide caliper calibration should verify that the measuring faces are not pitted, scratched, or corroded.
148. A warranty may exclude coverage for damage caused by exposure to dust, moisture, or corrosive atmospheres.
149. Source-grounded QA requires that calibration certificates be reviewed for completeness before release.
150. Infrared thermometer calibration should verify that the instrument’s reading is stable over the specified response time.
151. Digital multimeter calibration should verify that the instrument’s input protection does not trigger falsely under normal conditions.
152. Slide caliper calibration should verify that the zero position is repeatable after opening and closing the jaws.
153. Warranty documentation should state the procedure for filing a claim and the required documentation.
154. QA for precision instruments should include verification that the calibration environment meets the manual’s temperature and humidity requirements.
155. Infrared thermometer calibration may require a reference source with a temperature range that covers the instrument’s full range.
156. Digital multimeter calibration should verify that the instrument’s measurement uncertainty is within the stated specification.
157. Slide caliper calibration should verify that the gauge blocks are clean and free from oxidation before use.
158. A warranty may require that the instrument be returned to the manufacturer for warranty service.
159. Source-grounded QA requires that calibration records be auditable and traceable to the original source documents.
160. Infrared thermometer calibration should record the instrument’s serial number and model number in the calibration record.
161. Digital multimeter calibration should verify that the instrument’s battery voltage is within the specified range.
162. Slide caliper calibration should verify that the measuring range is not exceeded during calibration.
163. Warranty coverage may be limited to the original country of purchase.
164. QA records should include the date of calibration and the next calibration due date.
165. Infrared thermometer calibration should verify that the instrument’s optical system is free from scratches or contamination.
166. Digital multimeter calibration may require verification of the instrument’s input current range using a calibrated current source.
167. Slide caliper calibration should verify that the measuring faces are perpendicular to the beam if specified.
168. A warranty may exclude coverage for damage caused by improper calibration procedures.
169. Source-grounded QA requires that calibration results be reviewed by a second qualified person if required by the quality system.
170. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by ambient air movement.
171. Digital multimeter calibration should verify that the instrument’s resistance measurement is not affected by lead resistance.
172. Slide caliper calibration should verify that the gauge block’s temperature is stabilized before measurement.
173. Warranty documentation should state the maximum repair time or replacement turnaround time.
174. QA for precision instruments should include verification that the calibration manual is stored in a controlled location.
175. Infrared thermometer calibration may require a reference source with a known temperature drift over time.
176. Digital multimeter calibration should verify that the instrument’s AC voltage measurement is not affected by waveform distortion.
177. Slide caliper calibration should verify that the measuring faces are not worn beyond the specified limit.
178. A warranty may require that the instrument be serviced only by authorized personnel.
179. Source-grounded QA requires that calibration data be stored in a format that preserves the original values.
180. Infrared thermometer calibration should verify that the instrument’s emissivity setting is correctly applied to the target.
181. Digital multimeter calibration may require verification of the instrument’s input capacitance range.
182. Slide caliper calibration should verify that the depth rod is not bent or damaged.
183. Warranty coverage may be extended if the instrument is registered with the manufacturer.
184. QA records should include the calibration standard’s uncertainty and the instrument’s measured uncertainty.
185. Infrared thermometer calibration should verify that the instrument’s target-to-spot ratio is appropriate for the target size.
186. Digital multimeter calibration should verify that the instrument’s continuity test is not triggered by low resistance.
187. Slide caliper calibration should verify that the measuring faces are not contaminated with oil or debris.
188. A warranty may exclude coverage for damage caused by exposure to high humidity.
189. Source-grounded QA requires that calibration certificates be stored with the instrument’s quality record.
190. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by background temperature.
191. Digital multimeter calibration may require verification of the instrument’s input protection against reverse polarity.
192. Slide caliper calibration should verify that the gauge block’s dimensions are within the stated tolerance.
193. Warranty documentation should state the conditions under which the warranty is void.
194. QA for precision instruments should include verification that the calibration manual is reviewed periodically.
195. Infrared thermometer calibration may require a reference source with a known emissivity of 0.95 or higher.
196. Digital multimeter calibration should verify that the instrument’s measurement range is not exceeded during calibration.
197. Slide caliper calibration should verify that the measuring faces are not chipped or cracked.
198. A warranty may require that the instrument be stored in a dry, dust-free environment.
199. Source-grounded QA requires that calibration records be protected from unauthorized alteration.
200. Infrared thermometer calibration should verify that the instrument’s temperature reading is repeatable within the stated accuracy.
201. Digital multimeter calibration may require verification of the instrument’s input impedance for current measurements.
202. Slide caliper calibration should verify that the measuring faces are not discolored or oxidized.
203. Warranty coverage may be limited to the original calibration certificate.
204. QA records should include the calibration standard’s traceability to a national metrology institute.
205. Infrared thermometer calibration should verify that the instrument’s optical axis is aligned with the target.
206. Digital multimeter calibration should verify that the instrument’s input terminals are not loose.
207. Slide caliper calibration should verify that the gauge block’s surface finish is suitable for measurement.
208. A warranty may exclude coverage for damage caused by exposure to high temperatures.
209. Source-grounded QA requires that calibration data be reviewed for consistency with previous calibrations.
210. Infrared thermometer calibration may require a reference source with a known temperature stability of ±0.1 °C.
211. Digital multimeter calibration should verify that the instrument’s input protection is not damaged.
212. Slide caliper calibration should verify that the measuring faces are not worn unevenly.
213. Warranty documentation should state the warranty’s geographic scope.
214. QA for precision instruments should include verification that the calibration manual is accessible during calibration.
215. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by target motion.
216. Digital multimeter calibration may require verification of the instrument’s input protection against overcurrent.
217. Slide caliper calibration should verify that the gauge block’s dimensions are not affected by temperature.
218. A warranty may require that the instrument be calibrated by an accredited laboratory.
219. Source-grounded QA requires that calibration records be retained for the required period.
220. Infrared thermometer calibration should verify that the instrument’s emissivity setting is appropriate for the target material.
221. Digital multimeter calibration should verify that the instrument’s input terminals are not corroded.
222. Slide caliper calibration should verify that the measuring faces are not contaminated with abrasive particles.
223. Warranty coverage may be limited to the original purchaser.
224. QA records should include the calibration standard’s calibration date and due date.
225. Infrared thermometer calibration may require a reference source with a known temperature range of 0 to 1000 °C.
226. Digital multimeter calibration should verify that the instrument’s input protection is not triggered under normal conditions.
227. Slide caliper calibration should verify that the gauge block’s surface is not scratched.
228. A warranty may exclude coverage for damage caused by exposure to corrosive gases.
229. Source-grounded QA requires that calibration data be stored in a secure, auditable system.
230. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by ambient light.
231. Digital multimeter calibration may require verification of the instrument’s input protection against static discharge.
232. Slide caliper calibration should verify that the measuring faces are not pitted.
233. Warranty documentation should state the warranty’s start and end dates.
234. QA for precision instruments should include verification that the calibration manual is the current revision.
235. Infrared thermometer calibration should verify that the instrument’s optical system is not obstructed.
236. Digital multimeter calibration should verify that the instrument’s input terminals are not loose or damaged.
237. Slide caliper calibration should verify that the gauge block’s dimensions are within the stated uncertainty.
238. A warranty may require that the instrument be stored in a protective case.
239. Source-grounded QA requires that calibration records be reviewed for completeness.
240. Infrared thermometer calibration may require a reference source with a known emissivity of 1.0.
241. Digital multimeter calibration should verify that the instrument’s input protection is not degraded.
242. Slide caliper calibration should verify that the measuring faces are not contaminated with oil.
243. Warranty coverage may be limited to the original calibration interval.
244. QA records should include the calibration standard’s uncertainty and the instrument’s measured deviation.
245. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by target emissivity variation.
246. Digital multimeter calibration may require verification of the instrument’s input protection against voltage spikes.
247. Slide caliper calibration should verify that the gauge block’s surface is not oxidized.
248. A warranty may exclude coverage for damage caused by exposure to high pressure.
249. Source-grounded QA requires that calibration data be backed up regularly.
250. Infrared thermometer calibration should verify that the instrument’s optical axis is not misaligned.
251. Digital multimeter calibration should verify that the instrument’s input terminals are not contaminated.
252. Slide caliper calibration should verify that the measuring faces are not worn beyond the specified limit.
253. Warranty documentation should state the warranty’s terms and conditions.
254. QA for precision instruments should include verification that the calibration manual is stored securely.
255. Infrared thermometer calibration may require a reference source with a known temperature stability of ±0.05 °C.
256. Digital multimeter calibration should verify that the instrument’s input protection is not damaged by overvoltage.
257. Slide caliper calibration should verify that the gauge block’s dimensions are not affected by wear.
258. A warranty may require that the instrument be calibrated at regular intervals.
259. Source-grounded QA requires that calibration records be accessible for audit.
260. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by target distance.
261. Digital multimeter calibration may require verification of the instrument’s input protection against reverse voltage.
262. Slide caliper calibration should verify that the measuring faces are not contaminated with dust.
263. Warranty coverage may be limited to the original country of manufacture.
264. QA records should include the calibration standard’s traceability and uncertainty.
265. Infrared thermometer calibration should verify that the instrument’s optical system is not degraded.
266. Digital multimeter calibration should verify that the instrument’s input terminals are not loose.
267. Slide caliper calibration should verify that the gauge block’s surface is not scratched or pitted.
268. A warranty may exclude coverage for damage caused by exposure to high humidity.
269. Source-grounded QA requires that calibration data be stored in a controlled format.
270. Infrared thermometer calibration may require a reference source with a known emissivity of 0.98.
271. Digital multimeter calibration should verify that the instrument’s input protection is not triggered under normal conditions.
272. Slide caliper calibration should verify that the measuring faces are not contaminated with abrasive particles.
273. Warranty documentation should state the warranty’s coverage period.
274. QA for precision instruments should include verification that the calibration manual is reviewed annually.
275. Infrared thermometer calibration should verify that the instrument’s temperature reading is not affected by ambient temperature.
276. Digital multimeter calibration may require verification of the instrument’s input protection against overcurrent.
277. Slide caliper calibration should verify that the gauge block’s dimensions are within the stated tolerance.
278. A warranty may require that the instrument be stored in a dry environment.
279. Source-grounded QA requires that calibration records be protected from loss.
280. Infrared thermometer calibration should verify that the instrument’s optical axis is aligned with the target.
281. Digital multimeter calibration should verify that the instrument’s input terminals are not corroded or damaged.
282. Slide caliper calibration should verify that the measuring faces are not worn unevenly.
283. Warranty coverage may be limited to the original calibration certificate.
284. QA records should include the calibration standard’s calibration date and due date.
285. Infrared thermometer calibration may require a reference source with a known temperature range of -50 to 500 °C.
286. Digital multimeter calibration should verify that the instrument’s input protection is not degraded by moisture.
287. Slide caliper calibration should verify that the gauge block’s surface is not oxidized or corroded.
288. A warranty may exclude coverage for damage caused by exposure to high temperatures.
289. Source-grounded QA requires that calibration data be stored in a secure system.
290. Infrared thermometer calibration should verify that the instrument’s optical system is not obstructed or contaminated.
291. Digital multimeter calibration may require verification of the instrument’s input protection against voltage spikes.
292. Slide caliper calibration should verify that the measuring faces are not contaminated with oil or debris.
293. Warranty documentation should state the warranty’s terms